home 
wiki
wiki
VoyageLinux
Partition the CF card
[root@localhost ~]# fdisk /dev/hde
Command (m for help): n
Command action
e extended p primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-980, default 1):
Using default value 1
Last cylinder or +size or +sizeM or +sizeK (1-980, default 980):
Using default value 980
Command (m for help): a
Partition number (1-4): 1
Command (m for help): w
The partition table has been altered!
Calling ioctl() to re-read partition table.
Syncing disks
[root@localhost ~]#
Format the CF Card
[root@localhost ~]# mkfs.ext2 /dev/hde1
Transfer to Compact Flash card
Voyage Linux requires at least 64MB storage to run. However, 128MB is necessary if you want to add more software and be able to run "apt-get upgrade".
voyage.update scripts will ask you a couple of questions to complete the installation:
1. Voyage Linux software package directoy. (default to current path)
2. The target device to install Voyage Linux. (default to /dev/hde)
3. The temporary mount point for the disk device (default to /dev/mnt).
4. The module configuration to install
It will take a short while (~1 min) to copy all files from software package to disk device. The above configuration will be saved to .voyage.config. If you
run voyage.update next time, it will use same configuration as default.
[root@localhost voyage-0.2pre1]# ./voyage.update
Welcome to the Voyage Linux installation script
Loading defaults from .voyage.config
Where is the Voyage Linux installer (this) directory? (default=/root/voyage-0.2pre1):
Which device accesses the disk? (default=/dev/hde):
Which directory should the disk or flash card mount? (default=/media/idedisk):
Which module to install?
1 - WRAP
2 - 4501/4801
3 - 4511/4521
4 - Notebook (pcmcia)
5 - Generic PC
(default=1):1
Saving defaults to .voyage.config
Configuration completed:
-----------------------
Installer directory: /root/voyage-0.2pre1
Disk/Flash Device: /dev/hdeWill be mounted on: /media/idedisk
Installation mode: 1
If press RETURN to start installation, otherwise hit CTRL+C
Installing . . .
Connect to Wrap Board via serial console
Use a serial terminal program such as Minicom(Linux), Hyperterminal(Windows) to connect to the wrap board, set with the following settings ==> 9600 N 8 1.
Plug the flash card into your Wrap board and turn it on.
On the first boot of voyage the console will as you to enter the Roots password
Click to see full boot capture
PC Engines WRAP.2B/2C v1.04
640 KB Base Memory
15360
31744
48128
64512 KB Extended Memory
01F0 Master 848A SanDisk SDCFH-256
Phys C/H/S 980/16/32 Log C/H/S 980/16/32
LILLOO 2222..66..11 LLooaaddiinngg LLiinnuuxx....................................
BBIIOOSS ddaattaa cchheecckk ssuucccceessssffuull
Linux version 2.6.8-486-voyage (root@punknix-uml) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Tue Jul 12 04:06:34 GMT 2005
Setup Network Connections
Edit /etc/network/interface and uncomment the interface configuration section:
#Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or
#/usr/share/doc/ifupdown/examples for more information.
auto eth0
iface eth0 inet static
address 10.10.***.**
netmask 255.255.255.240auto ath0
iface ath0 inet static
address 10.10.***.***
netmask 255.255.255.240
gateway 10.10.***.***
pre-up iwpriv ath0 mode 3
pre-up iwconfig ath0 essid "***.melbournewireless.org.au" mode master channel 1 auto ath1
iface ath1 inet static
address 10.10.***.***
netmask 255.255.255.240
broadcast 10.10.***.***Or Set it up for bridge mode
#Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or
#/usr/share/doc/ifupdown/examples for more information.
auto lo
iface lo inet loopback
auto br0
iface br0 inet static
address 10.10.***.***
netmask 255.255.255.240
gateway 10.10.***.***
bridge_ports eth0 ath0
pre-up ifconfig eth0 0.0.0.0 up
pre-up ifconfig ath0 0.0.0.0 up
pre-up iwpriv ath0 mode 3
pre-up iwconfig ath0 essid "***.melbournewireless.org.au" mode master channel 1
pre-up brctl addbr br0
pre-up brctl addif br0 eth0
pre-up brctl addif br0 ath0
post-down ifconfig eth0 0.0.0.0 down
post-down ifconfig ath0 0.0.0.0 down
post-down brctl delif br0 eth0
post-down brctl delif br0 ath0
post-down brctl delbr br0Setup DHCP
By default dhcp is not enabled. To enable DHCP, edit /etc/dnsmasq.conf and add the following lines at the end of the file:
dhcp-range=ath0,10.10.***.***,10.10.***.***,24h
dhcp-leasefile=/var/tmp/dnsmasq.leases
dnsmasq will provide IP address leases between the 2 ranges
Setup Time zone
remountrw
ln -sf /usr/share/zoneinfo/Australia/Melbourne /etc/localtime
remountro
Install thttpd web sever
Download and untar the thttpd-php binary.
remountrw
cd /rw
wget http://www.pure-wireless.net/thttpd-voyage.tar.gz
tar zxf thttpd-voyage.tar.gz
cd thttpd
Move the files to their required locations.
mv etc/init.d/thttpd /etc/init.d/
mv etc/logrotate.d/thttpd /etc/logrotate.d/
mv etc/thttpd /etc/
mv usr/sbin/thttpd /usr/sbin/thttpd
Create the user to run under and the data director.
useradd www
mkdir /var/www/
remountro
Download Quagga
Download and install the quagga package
remountrw
apt-get update
apt-get install quagga
mkdir /ro/var/run/quagga
mkdir /ro/var/quagga
chmod 777 /ro/var/run/quagga
chmod 777 /ro/var/quagga
fastreboot
Turn zebra & ospfd on in the /etc/quagga/daemons file
Create zebra.conf & ospfd.conf files in the /etc/quagga directory
Version 2 (current) modified Mon, 26 Jul 2021 12:49:29 +0000 by mjc
[EditText] [Spelling] [Current] [Raw] [Code] [Diff] [Subscribe] [VersionHistory] [Revert] [Delete] [RecentChanges]